1 nic components corp. www.niccomp.com www.lowesr.com www.rfpassives.com www.smtmagnetics.com specifications are subject to change miniature aluminum electrolytic capacitors radial leads, polarized, new further reduced case sizing, from nrwa wide temperature range nrws series characteristics note: capacitors shall conform to jis-c-5141, unless otherwise speci ed here. *1. add 0.5 every 1000 f for more than 1000f *2. add 1.0 every 1000f for more than 1000f ex tend ed tem per a ture nrwa nrws (today?s standard) (reduced sizes) rated voltage range 6.3 ~ 100vdc capacitance range 2.2 ~ 15,000 f operating temperature range -55c ~ +105c capacitance tolerance 20% (m) maximum leakage current @ +20c after 1 min. 0.03cv or 4a whichever is greater after 2 min. 0.01cv or 3a whichever is greater max. tan at 120hz/20c w.v. (vdc) 6.3 10 16 25 35 50 63 100 s.v. (vdc) 8 13 20 32 44 63 79 125 c < 1,000 f 0.28 0.24 0.20 0.16 0.14 0.12 0.10 0.08 c = 2,200 f 0.30 0.26 0.22 0.18 0.16 0.14 - - c = 3,300 f 0.32 0.28 0.24 0.20 0.18 0.16 - - c = 4,700 f 0.34 0.30 0.26 0.22 0.20 - - - c = 6,800 f 0.36 0.32 0.28 0.24 ---- c = 10,000 f 0.38 0.34 0.30 ----- c = 15,000 f 0.56 0.52 ------ low temperature stability impedance ratio @ 120hz z-25c/z+20c 54322222 z-40c/z+20c 12 10 854444 load life test at +105c & rated w.v 2,000 hours: 16v ~ 100v d> 10 1,000 hours: all others capacitance within 20% of initial measured value tan less than 200% of speci ed value lc less than speci ed value shelf life test +105c 1,000 hours no load capacitance within 20% of initial measured value tan less than 200% of speci ed value lc less than speci ed value lead spacing and diameter (mm) cap. ( f) code working voltage (vdc) 6.3 10 16 25 35 50 63 100 2.2 2r2 - - - - - 5x11 5x11 - 3.3 3r3 - - - - - 5x11 5x11 - 4.7 4r7 - - - - - 5x11 5x11 - 10 100 - - - - - 5x11 5x11 - 22 220 - - - - - 5x11 5x11 8x11.5 33 330 - - - - 5x11 5x11 6.3x11 8x12.5 47 470 - - - 5x11 5x11 6.3x11 6.3x11 10x12.5 100 101 - 5x11 5x11 6.3x11 6.3x11 8x11.5 8x12.5 10x20 220 221 5x11 6.3x11 6.3x11 8x11.5 8x11.5 10x12.5 10x16 12.5x25 330 331 6.3x11 6.3x11 8x11.5 8x11.5 10x12.5 10x16 10x20 16x25 470 471 6.3x11 6.3x11 8x11.5 10x12.5 10x16 10x20 12.5x20 16x31 1,000 102 8x11.5 10x12.5 10x16 10x20 12.5x20 12.5x25 16x25 - 2,200 222 10x16 10x20 12.5x20 12.5x25 16x25 16x31 - - 3,300 332 10x20 12.5x20 12.5x25 16x25 16x35 18x36 - - 4,700 472 12.5x20 12.5x25 16x25 16x31 18x36 - - - 6,800 682 12.5x25 16x25 16x31 18x36 - - - - 10,000 103 16x25 16x31 18x36 - - - - - 15,000 153 16x36 18x36 - - - - - - case dia. (d ) 5 6.3 8 10 12.5 16 18 lead dia. (d ) 0.5 0.5 0.6 0.6 0.6 0.8 0.8 lead spacing (f) 2.0 2.5 3.5 5.0 5.0 7.5 7.5 dim. 0.5 0.5 0.5 0.5 0.5 0.5 0.5 standard product and case size table d xl (mm) *see part number system for details p n bs fd il rohs compliant includes all homogeneous materials ? meets the requirements of aec-q200* *contact nic for supporting test data
2 nic components corp. www.niccomp.com www.lowesr.com www.rfpassives.com www.smtmagnetics.com specifications are subject to change miniature aluminum electrolytic capacitors nrws series part number cap. (f) w.v. (vdc) dissipation factor +20c/120hz ripple current rating (ma) +105c/100khz max. impedance () +20c/100khz load life hours @+105c nrws221m6.3v5x11f 220 6.3 0.28 160 1.40 1,000 nrws331m6.3v6.3x11f 330 0.28 240 0.58 1,000 nrws471m6.3v6.3x11f 470 0.28 250 0.55 1,000 nrws102m6.3v8x11.5f 1,000 0.28 450 0.26 1,000 nrws222m6.3v10x16f 2,200 0.30 760 0.12 2,000 nrws332m6.3v10x20f 3,300 0.32 900 0.10 2,000 nrws472m6.3v12.5x20f 4,700 0.34 1100 0.072 2,000 nrws682m6.3v12.5x25f 6,800 0.36 1420 0.054 2,000 nrws103m6.3v16x25f 10,000 0.38 1700 0.043 2,000 nrws153m6.3v16x36f 15,000 0.56 2100 0.032 2,000 nrws101m10v5x11f 100 10 0.24 150 1.40 1,000 nrws221m10v6.3x11f 220 0.24 240 0.58 1,000 nrws331m10v6.3x11f 330 0.24 250 0.55 1,000 nrws471m10v6.3x11f 470 0.24 370 0.39 1,000 nrws102m10v10x12.5f 1,000 0.24 560 0.16 2,000 nrws222m10v10x20f 2,200 0.26 900 0.10 2,000 nrws332m10v12.5x20f 3,300 0.28 1100 0.074 2,000 nrws472m10v12.5x25f 4,700 0.30 1420 0.054 2,000 nrws682m10v16x25f 6,800 0.32 1700 0.043 2,000 nrws103m10v16x31f 10,000 0.34 1950 0.035 2,000 nrws153m10v18x36f 15,000 0.52 2400 0.028 2,000 nrws101m16v5x11f 100 16 0.20 150 1.40 1,000 nrws221m16v6.3x11f 220 0.20 240 0.55 1,000 nrws331m16v8x11.5f 330 0.20 370 0.35 1,000 nrws471m16v8x11.5f 470 0.20 450 0.28 1,000 nrws102m16v10x16f 1,000 0.20 760 0.13 2,000 nrws222m16v12.5x20f 2,200 0.22 1100 0.075 2,000 nrws332m16v12.5x25f 3,300 0.24 1320 0.054 2,000 nrws472m16v16x25f 4,700 0.26 1600 0.043 2,000 nrws682m16v16x31f 6,800 0.28 1900 0.035 2,000 nrws103m16v18x36f 10,000 0.30 2300 0.028 2,000 nrws470m25v5x11f 47 25 0.16 150 1.40 1,000 nrws101m25v6.3x11f 100 0.16 240 0.60 1,000 nrws221m25v8x11.5f 220 0.16 370 0.39 1,000 nrws331m25v8x11.5f 330 0.16 400 0.34 1,000 nrws471m25v10x12.5f 470 0.16 560 0.17 2,000 nrws102m25v10x20f 1,000 0.16 900 0.10 2,000 nrws222m25v12.5x25f 2,200 0.18 1320 0.062 2,000 nrws332m25v16x25f 3,300 0.20 1600 0.043 2,000 nrws472m25v16x31f 4,700 0.22 1900 0.035 2,000 nrws682m25v18x36f 6,800 0.24 2200 0.028 2,000 nrws330m35v5x11f 33 35 0.14 120 2.10 1,000 nrws470m35v5x11f 47 0.14 140 2.10 1,000 nrws101m35v6.3x11f 100 0.14 180 1.10 1,000 nrws221m35v8x11.5f 220 0.14 360 0.46 1,000 nrws331m35v10x12.5f 330 0.14 580 0.26 1,000 nrws471m35v10x16f 470 0.14 650 0.18 1,000 nrws102m35v12.5x20f 1,000 0.14 900 0.11 2,000 nrws222m35v16x25f 2,200 0.16 1400 0.056 2,000 nrws332m35v16x35f 3,300 0.18 1800 0.038 2,000 nrws472m35v18x36f 4,700 0.20 2000 0.035 2,000 nrws2r2m50v5x11f 2.2 50 0.12 40 5.5 1,000 nrws3r3m50v5x11f 3.3 0.12 50 4.0 1,000 nrws4r7m50v5x11f 4.7 0.12 80 2.80 1,000 nrws100m50v5x11f 10 0.12 90 2.30 1,000 nrws220m50v5x11f 22 0.12 110 2.20 1,000 standard values, specifications and case sizes (mm) for automotive applications see part number system
3 nic components corp. www.niccomp.com www.lowesr.com www.rfpassives.com www.smtmagnetics.com specifications are subject to change ripple current correction factors cap. (f) frequency (hz) 100 1k 10k ~ ~ 47 0.50 0.80 1.0 > 47 ~ 220 0.55 0.85 1.0 > 220 ~ 1,000 0.65 0.90 1.0 > 1,000 0.75 0.90 1.0 part number cap. (f) w.v. (vdc) dissipation factor +20c/120hz ripple current rating (ma) +105c/100khz max. impedance () +20c/100khz load life hours @+105c nrws330m50v5x11f 33 50 0.12 120 2.10 1,000 nrws470m50v6.3x11f 47 0.12 180 1.10 1,000 nrws101m50v8x11.5f 100 0.12 310 0.55 1,000 nrws221m50v10x12.5f 220 0.12 500 0.30 2,000 nrws331m50v10x16f 330 0.12 650 0.20 2,000 nrws471m50v10x20f 470 0.12 800 0.13 2,000 nrws102m50v12.5x25f 1,000 0.12 1100 0.10 2,000 nrws222m50v16x31f 2,200 0.14 1650 0.055 2,000 nrws332m50v18x36f 3,300 0.16 2000 0.035 2,000 nrws2r2m63v5x11f 2.2 63 0.10 42 8.3 1,000 nrws3r3m63v5x11f 3.3 0.10 58 6.0 1,000 nrws4r7m63v5x11f 4.7 0.10 64 4.20 1,000 nrws100m63v5x11f 10 0.10 90 2.80 1,000 nrws220m63v5x11f 22 0.10 140 2.40 1,000 nrws330m63v6.3x11f 33 0.10 200 1.40 1,000 nrws470m63v6.3x11f 47 0.10 240 1.30 1,000 nrws101m63v8x12.5f 100 0.10 300 0.60 1,000 nrws221m63v10x16f 220 0.10 520 0.22 2,000 nrws331m63v10x20f 330 0.10 765 0.17 2,000 nrws471m63v12.5x20f 470 0.10 960 0.14 2,000 nrws102m63v16x25f 1,000 0.10 1100 0.065 2,000 nrws220m100v8x11.5f 22 100 0.08 235 0.83 1,000 nrws330m100v8x12.5f 33 0.08 300 0.60 1,000 nrws470m100v10x12.5f 47 0.08 330 0.39 2,000 nrws101m100v10x20f 100 0.08 450 0.24 2,000 nrws221m100v12.5x25f 220 0.08 700 0.15 2,000 nrws331m100v16x25f 330 0.08 950 0.09 2,000 nrws471m100v16x31f 470 0.08 1100 0.085 2,000 precautions please review the notes on correct use, safety and precautions found on pages t10 & t11 of nic?s electrolytic capacitor catalog. also found at www.niccomp.com/precautions if in doubt or uncertainty, please review your speci c application - process details with nic?s technical support personnel: tpmg@niccomp.com miniature aluminum electrolytic capacitors nrws series standard values, specifications and case sizes (mm) = l < 20mm = 1.5mm, l > 20mm = 2.0mm for automotive applications see part number system part number system nrws 101 m 35v 6.3x11 tb y f . rohs compliant tb = tape & box* case size (d xl) working voltage (vdc) tolerance code (m=20%) capacitance code: first 2 characters signi cant, third character is multiplier series *see taping speci cations for details optional: for automotive equipment, sourced to special production and inspection at ts-16949 certi ed production site dimensions (mm) d 0.05 sleeve f 0.5 d 4mm min. 15mm min. l + max. polarity marking drawing is representative of parts as supplied in bulk or straight lead format, please see taping speci cation for details on taped format packaging. - +
|
